Essential Plumber Insights for Bathtub Installation
Essential Plumber Insights for Bathtub Installation
Blog Article
Here below you can locate a bunch of extremely good content regarding How to Install a Bathtub.
Installing a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging project. If the old tub is conveniently accessible, the task can move immediately; if you have to open up a wall to eliminate the old tub and also place the new tub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will require a helper to vacate the old tub as well as set in the new one. Ensure you have actually certified yourself for the work and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is much better to consider employing one before you start. Possibilities are you may need an expert plumber to make tube links.
This write-up will aid you install a brand-new bathtub in your bathroom if you have actually already bought a brand-new bathtub and also don't require to transform the setup of your previous water supply pipelines.
Your devices and also material list need to make up the following:
Getting ready for the Installation
First of all, the supporting structure provided with the bath must be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning during this process. Once the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, position the bath tub in the needed setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bath tub till the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the supply of water as well as inspect all joints and new pipework for leaks and tighten them if essential. Fill the bath tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and securing around the bathtub must wait until the tub has actually been used at the very least when as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap and the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind must be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, causing difficulties with dampness and also feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can break rather very early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that page on How to Install a Bathtub while doing a lookup on the search engines. Sharing is good. You just don't know, you may be helping someone out. Thank you for going through it.
Clog problems? Inform. Report this page